Food Drying Lines and Turnkey Dehydration Plants
Complete production lines built around the drying step: washing and sorting, multi-zone drying, cooling and moisture equalising, then grading, milling or packing. Every line on this page is sized from the water it must remove, configured to your local energy price, and shipped with installation, commissioning and training.

A food drying line takes fresh material from 75-90% moisture down to a stable 5-18% and delivers it as a saleable grade: whole dried pods, flakes, powder, slices or pieces. The line is sized by how much water you must remove per day, not by how much raw material you buy.
There are two machine families. Heat pump drying rooms hold 20-80°C within ±1°C and suit colour-sensitive, high-value products at 0.5-5 t per batch. Multi-layer mesh belt dryers run 60-120°C continuously and suit one product at high volume, from 500 kg/h upward.
Budget USD 4,000-25,000 for an entry drying room, USD 40,000-200,000+ for a continuous line, and USD 150,000-350,000 landed for a complete 2-5 t/day dehydration plant. Equipment is only 35-55% of a landed project – freight, customs, civil works, utilities, installation, commissioning and training make up the rest.
Drying Lines You Can Order Today

Chili Drying Line
Fresh pods at 75-85% moisture dried to 10-13% in 8-20 hours through multi-zone control, then graded whole or milled into flake and powder. Configured as heat pump rooms for colour-critical export lots or as a multi-layer belt line for continuous volume.
- Moisture 75-85% to 10-13%
- Temperature 55-75°C, multi-zone
- Yield 4-6 : 1 fresh to dried
- Cycle 8-20 h
- Equipment USD 25k-250k+
- Payback 1.5-3 years

Dehydrated Onion Line
Bulbs at 80-85% moisture sliced to 3-5 mm and dried through three zones to 5-7%, then milled into flakes, kibbled, minced or 60-100 mesh powder. Built around browning control, because colour is what decides the export grade.
- Moisture 80-85% to 5-7%
- Curve 55-60 / 65-75 / 55-60°C
- Grades Flakes, kibbled, minced, powder
- Slice 3-5 mm
- Equipment USD 40k-300k
- Output 7-9 : 1 fresh to dried

Drying Line Cost and Payback
What a drying project actually costs to land, and how fast it pays back. Equipment budget by capacity tier, the cost blocks most suppliers leave out, energy cost per kg of water removed, and a payback calculation you can run at your own electricity tariff.
- Equipment 35-55% of landed cost
- Landed overhead 45-65%
- Heat pump 0.35-0.55 kWh/kg water
- Electric hot air 1.0-1.4 kWh/kg
- Range USD 4k to USD 350k+
- Payback 1.5-3 years

Garlic Dehydration Line
Peeled cloves at 62-68% moisture sliced to 2-3 mm and dried below 65°C to protect allicin, then milled into flakes, granules and 80-100 mesh powder. Built around colour and pungency – the two things garlic buyers grade on.
- Moisture 62-68% to below 6%
- Curve 55-65°C allicin-safe
- Grades Flakes, granules, powder
- Yield 3-3.5 : 1
- Equipment USD 45k-320k
- Mesh 80-100 powder

Mango Drying Line
Fresh fruit at 80-85% moisture dried to a soft-chewy 15-18% in heat pump rooms at 55-65°C for 8-14 h, with a colour-protecting dip and export colour grading. The gentle curve is what keeps the golden grade buyers pay a premium for.
- Moisture 80-85% to 15-18%
- Curve 55-65°C heat pump
- Cycle 8-14 h per batch
- Yield 5-8 : 1 fresh to dried
- Equipment USD 35k-350k
- Grade Export colour classes

Mixed Vegetable Dehydration Line
Carrot, cabbage, green pepper, onion and leek on one continuous line: change the cutter die and the recipe, keep the dryer. Diced to 5×5 or 10×10 mm for soup packs and food service, with utilisation engineered into the design.
- Moisture 85-92% to 5-8%
- Cut 5×5 / 10×10 mm dice
- Coverage Carrot to leafy greens
- Yield 8-15 : 1 by product
- Equipment USD 50k-320k
- Utilisation 70%+ year-round

Ginger & Turmeric Drying Line
Washing with destoning, 2-4 mm slicing, drying at 60-70°C below the oleoresin threshold, then fibre separation and 80-100 mesh milling. Turmeric campaigns add a steam-cooking module that sets the deep colour before drying.
- Moisture 85-90% to 10-12%
- Curve 60-70°C protected
- Grades Slices and 80-100 mesh powder
- Yield 6-9 : 1 ginger
- Equipment USD 40k-300k
- Module Turmeric steam-cook

Banana & Plantain Drying Line
Non-fried drying: 2-3 mm slices with a citric-acid dip dried at 55-65°C to below 13% moisture, plus a flour route that mills green bananas and plantain into 30-150 mesh gluten-free flour from fruit the fresh market rejects.
- Moisture 75-80% to below 13%
- Curve 55-65°C no-fry
- Products Slices or 30-150 mesh flour
- Flour yield 22-28% of green
- Equipment USD 35k-300k
- Fry section None

Multi-Product Drying Line
The full switching matrix: what changes between chili, onion, garlic, ginger, vegetables, fruit and herbs on one dryer. Quick-change dies, saved PLC recipes and 70%+ utilisation – which roughly halves the payback period.
- Products 8+ families on one dryer
- Changeover 2-4 h
- Utilisation 35% to 70%+
- Payback Roughly halved
- Equipment +5-12% on line price
- Coverage 40-80°C recipes

Mushroom Drying Line
Button, oyster and shiitake from 90-95% to 8-12% moisture on gentle 45-60°C curves that hold the aroma and rehydration buyers test for. Sliced, whole-cap or powder grades, built around the 2-3 day pick-to-dryer window.
- Moisture 90-95% to 8-12%
- Curve 45-60°C, aroma-protecting
- Yield 9-12 : 1
- Forms Sliced, whole caps, powder
- Equipment USD 25k-220k
- Config Rooms or belt

Fish & Seafood Drying Line
A dedicated SUS316 line with its own hygiene zoning: gutting, splitting and brining, then heat pump drying at 25-45°C for salted fish, stockfish, shrimp and squid – never shared with plant products.
- Steel SUS316 product contact
- Curve 25-45°C heat pump
- Yield 2.5-3.5 : 1 split fish
- Cycle 1-7 days by route
- Equipment USD 30k-280k
- Zoning Dedicated meat/fish flow

Jerky & Pet Treat Drying Line
Sliced, marinated meat with a verified 71°C core cook step, then 55-70°C drying to 25-30% jerky or below-12% pet treats. Dedicated meat hygiene zone, batch cook logs and water-activity QC built in.
- Cook step 71°C core, logged
- Jerky 25-30% moisture
- Pet treats Below 12%
- Yield 2-3 : 1 raw to finished
- Equipment USD 25k-250k
- QC Moisture + water activity

Cassava Drying & Flour Line
Peel, grate, ferment and press for gari and fufu, or granulate and dry at 60-80°C for high-quality cassava flour. The dewatering press does the heavy lifting before any fuel is spent.
- Moisture 60-70% to 10-12%
- Yield 2.5-3 : 1 peeled
- Routes Gari, fufu, HQCF
- Window 24-48 h post-harvest
- Equipment USD 30k-400k
- Fuel Biomass default

Tomato & Berry Drying Line
Halved tomatoes at 18-25:1 water removal to premium sundried packs or 3-5% powder, and berries dried at 45-60°C on colour-protected curves that keep the anthocyanin depth buyers grade by. Sulphite-free by design.
- Tomato 93-95% to 8-12% / 3-5%
- Berries 80-85% to 12-18%
- Curve 45-60°C colour-protected
- Yield 18-25 : 1 tomato
- Equipment USD 35k-320k
- Extras Powder & leather mill

Non-Fried Fruit & Vegetable Crisps Line
A crisp with no fryer: 2-3 mm slices of apple, banana, pineapple, jackfruit, sweet potato or beetroot dried at 45-60°C to 3-5% moisture, then seasoned and nitrogen-packed. Whole plant supplied, washers to packers.
- Moisture 80-90% to 3-5% crisp
- Curve 45-60°C
- Oil None added
- Shelf life 9-12 months
- Equipment USD 40k-340k
- Scope Wash, cut, dry, season, pack

Root Vegetable Dehydration Line
Potato, sweet potato, beetroot and carrot: destone, wash, peel, dice, blanch and dry at 65-80°C to dice, flakes, granules and 60-80 mesh powder, with every machine in the chain sized to one throughput.
- Moisture 75-85% to 5-8%
- Curve 65-80°C multi-zone
- Peel loss 15-30% by method
- Blanch 1-5 min
- Equipment USD 60k-520k
- Scope Peeler to mill, all ours

Coffee, Cocoa & Nut Drying Line
Export numbers you can guarantee: cocoa to 6-8%, coffee parchment to 11-12%, nuts below 8% for aflatoxin control. Fermentation decks, 45-60°C heat pump drying, sorting, grading and lot moisture records.
- Cocoa 6-8% export moisture
- Coffee 11-12% parchment
- Nuts Below 8%
- Curve 45-60°C controlled
- Equipment USD 30k-400k
- Instead of sun Rain-independent

Herb & Spice Drying Line
Leaf herbs, seed spices and edible flowers dried at 35-50°C on heat pump rooms so the volatile oils and the colour stay in the leaf. Whole-leaf, cut-and-rubbed and powder grades from one plant.
- Moisture 75-85% to 8-12%
- Curve 35-50°C
- Yield 6-12 : 1 leaf herbs
- Grades Whole, rubbed, powder
- Equipment USD 25k-260k
- Key machine Air-blow dewaterer

Date, Fig & Jujube Drying Line
Dates, figs and jujubes dried on a staged 50-65°C heat pump curve after brush washing and a wax-cracking dip, finishing at 18-24% moisture for the soft-chew grade. Built to stop sugar migrating to the surface – the defect that turns sun-dried lots sticky and dark.
- Moisture 60-75% to 18-24%
- Curve 50-65°C staged
- Yield 3-4 : 1 fresh to dried
- Cycle 24-48 h
- Equipment USD 18k-180k
- Key control Sugar migration

Tea Leaf Drying Line
Two-stage tea drying: a fast 90-120°C belt pass to arrest oxidation, then gentle 70-90°C heat pump finishing to 4-6% moisture that keeps the aroma in the leaf. Withering, rolling or fix-green, sorting and packing complete the chain for green, black and herbal programmes.
- Moisture 75-80% to 4-6%
- Belt 90-120°C primary
- Finish 70-90°C heat pump
- Yield 4-5 : 1 fresh to made
- Equipment USD 15k-220k
- Key control Aroma retention

Plant Layout & Utility Requirements
The building numbers behind every drying project: line length, width and clear height by capacity tier, power supply sizing, steam and biomass options, water, drainage, floor loads and container counts – plus straight, L and U layout trade-offs.
- Length 8-90 m by tier
- Height 3.5-6 m clear
- Power 18-540 kW classes
- Freight 1-12 x 40HQ
- Floor 3-5 t point load
- Layouts Straight, L, U

Turnkey Drying Project Process
The whole project on one page: drying test on your own material, layout-backed quotation, manufacturing with factory test records, container shipping, 15-30 day installation, 2-5 day commissioning, operator training and one spares catalogue.
- Test 3-5 kg of your material
- Build 8-14 weeks
- Install 15-30 days on site
- Commission 2-5 days per line
- Training Operators + maintenance
- Spares One catalogue

Pre-Treatment Line
Bubble and vortex washing, brush washer-peelers for roots, cutting, blanching and mechanical dewatering – the wet end that decides drying quality. Supplied with the dryer or standalone for plants upgrading an existing machine; dewatering alone cuts dryer load 10-20%.
- Machines Wash, peel, cut, blanch
- Dewater Centrifugal or air
- Throughput 0.5-5 t/h classes
- Energy Cuts dryer load 10-20%
- Equipment USD 3.5k-60k
- Retrofit Matched to your dryer

Post-Treatment Line
Cooling, moisture conditioning, grading, hammer milling to 20-100 mesh powder grades, metal detection and barrier packing. The section that turns dryer output into a certified, sellable product – milling alone lifts order value 30-50% on the same material.
- Condition 4-8 h moisture equalise
- Milling 20-100 mesh
- Safety Inline metal detection
- Packing Barrier bags, N2 option
- Equipment USD 4k-80k
- Value +30-50% with milling
Tell Us What You Dry – We Size The Line
- Material, variety and initial moisture
- Fresh input per day or per hour
- Target final moisture and finished grade
- Available heat source and factory dimensions
Prefer email? Write to info@tondemachine.com or WhatsApp +86 185 0387 4173. Our engineers reply within one working day.
The Full Line Series – What Is Coming Next
We are publishing one line page per material, each with the same data set: process flow, equipment list, three capacity tiers, utilities, floor space, labour, investment and payback. All 24 pages of the series are now live.
Tier 1 – Main material drying lines
Tier 2 – High-value lines
Tier 3 – Investment pages
Tier 4 – Process sections
How To Choose A Drying Line – Four Steps
1. Start with the water, not the machine
Fresh input multiplied by the moisture drop is how much water you must remove per day. That single number sizes the dryer, the heat source and the power feed. A 2 t/day chili plant removes about 1.5 t of water per day; everything else follows from that.
2. Check the temperature ceiling of your product
Colour-sensitive products – chili, herbs, flowers, fruit – need 40-65°C and precise control. Robust products – roots, cassava, grain – tolerate 80-120°C and dry far faster. The ceiling decides whether you buy a heat pump room or a belt dryer.
3. Match the heat source to your local energy
Steam where a boiler exists, gas where gas is cheap, biomass where agricultural waste is free, heat pump where electricity is expensive. Running cost over ten years usually exceeds the purchase price, so this choice matters more than the machine specification.
4. Plan the building before you order
Drying lines are long and narrow. Check straight length, width and clear height against the layout drawing, and run the power feed, drainage and water while the machines are being built – civil works are the most common cause of late start-up.
Which Machine Goes In Which Line
| Line | Machine | Why | Capacity |
|---|---|---|---|
| Chili, colour-critical lots | Heat pump drying room | 20-75°C, ±1°C control, 0.35-0.55 kWh/kg water | 0.5-5 t per batch |
| Chili, continuous export volume | Multi-layer mesh belt dryer | 3-5 zones, continuous feed and discharge | 500 kg-3 t/h |
| Onion, garlic, ginger | Multi-layer mesh belt dryer + mill | Three-zone curve protects white colour; one stream to powder | 300 kg-5 t/h |
| Mango, fruit slices | Heat pump room + tray or belt loading | 45-65°C protects colour and aroma | 0.5-5 t per batch |
| Cassava, roots, grain | Mesh belt or flash dryer | Tolerates 80-120°C; dries fast and cheap | 1-30 t/h |
| Herbs, flowers, tea | Heat pump room | 35-55°C keeps volatile oils and aroma | 0.3-3 t per batch |
Frequently Asked Questions
What is included in a turnkey drying line?
Process design, the drying and downstream machines, layout and utility drawings, manufacturing, container loading and shipping documents, then installation, commissioning and operator training at your site, with remote support afterwards. Pre-treatment equipment – washing, peeling, slicing – is included or integrated depending on what you already own.
How much does a drying line cost?
Indicative equipment budget: USD 4,000-25,000 for an entry batch dryer or drying room, USD 40,000-200,000+ for a continuous line, and USD 150,000-350,000 landed for a complete 2-5 t/day dehydration plant. Equipment is typically only 35-55% of a landed project – freight, customs, civil works, utilities, installation, commissioning and training add roughly 45-65%.
How long does it take from order to production?
Manufacturing 30-60 days, sea freight 25-45 days, customs and inland transport 1-3 weeks, installation, commissioning and training 2-4 weeks. Plan four to six months, and start civil works while the machines are being built.
Can one line handle several products?
Yes. Temperature, airflow and belt speed are saved as recipes on the PLC panel, and the changeover is usually a slicer or dice-size adjustment plus a recipe selection. Onion, garlic, ginger, carrot and chili can all run on one drying line; fish and meat are better on a dedicated line for hygiene reasons.
How many workers does a line need?
Typically 2-3 per shift for a small co-op line, 4-6 for a mid-size plant and 6-8 for an export plant: intake and sorting, one operator on the dryer panel, packing and palletising, plus a shared QA sampler. Industry-typical figures for a PLC-controlled line.
Do you test our material before quoting?
Yes. Send 2-5 kg of your material and we dry it on the machine type we are quoting, then return the drying curve, colour photos, shrinkage data and final moisture. Capacity and energy figures on the quotation are confirmed against that test, not taken from a catalogue.
Can the line run where power is unreliable?
Yes. Heating can be steam, biomass, gas, diesel or electric, and we add a generator-backed control circuit so the PLC and fans keep running and the batch is not lost. In many African and South Asian markets a biomass or hybrid configuration is the most reliable answer.
Where do I start if I am not sure which machine I need?
Send us three things: the material and its initial moisture, how much fresh material you have per day, and the final moisture your buyer requires. We will size the line, recommend the machine type and send a layout drawing with a budget range.
Request Your Turnkey Quotation
- Factory-direct price, no middleman
- Process design, layout drawing and utility specification
- Drying test with your own material before quotation
- Worldwide shipping, installation and remote commissioning support
Prefer email? Write to info@tondemachine.com or WhatsApp +86 185 0387 4173. Our engineers reply within one working day.