Drying Plant Layout and Utility Requirements | Building, Power, Steam and Water
Most drying projects are sized by budget first and building second – then the building bites back. Three numbers decide whether a line fits: straight-line length, power supply and heat source capacity. This page gives the working dimensions, utility loads and layout options for drying plants from a single heat pump room to a 90-metre continuous line, so you can check your site before you commit.

A drying plant needs three numbers checked before anything is ordered: straight-line length for the equipment chain, installed power (or steam/gas) for the heat load, and floor loading with drainage in the wet end. A room-based plant fits an 8×6 m shed; a continuous line needs 30-90 m of straight run.
Power classes: batch room plants run 18-80 kW, mid-size mixed lines 80-200 kW, and continuous belt lines 110-540 kW depending on the heat source. Biomass or gas heat replaces most of the electrical load where fuel is cheap.
Container planning: a room plant ships in 1-2 x 40HQ, a batch system in 3-5, and a full continuous plant in 6-12 x 40HQ. Equipment is typically only 35-55% of a landed project – the civil works, power feed and installation around it are planned on this page’s numbers.
Building Dimensions By Plant Type
| Item | Room plant (batch) | Mixed batch system | Continuous line | Data basis |
|---|---|---|---|---|
| Straight-line length | 8-12 m | 20-35 m | 40-90 m | B – industry |
| Width | 6-8 m | 8-12 m | 10-16 m | B – industry |
| Clear height | 3.5-4.5 m | 4.5-5 m | 5-6 m | B |
| Door size (widest) | 1.5×2 m | 2×2.2 m | 3×3 m for module entry | B |
| Floor | washable, drained | food-grade, 3 t point load | food-grade, 5 t point load, drains along the line | B – industry |
| Layout options | single row | straight or L | straight, L or U around packing | B |
Dimensions are for the equipment chain itself – add 2-3 m of working aisle on each side and space for trolleys, bins and pallet staging.
Power, Heat, Water and Air By Tier
| Utility | Room plant | Mixed batch system | Continuous line | Data basis |
|---|---|---|---|---|
| Electricity (installed) | 18-80 kW | 80-200 kW | 110-540 kW | B – industry |
| Steam (where used) | 0.3-1 t/h | 1-2.5 t/h | 2.5-6.5 t/h | C – estimate |
| Biomass/gas alternative | optional | 150-350 kg/h wood equiv. | 350-1000 kg/h wood equiv. | C – estimate |
| Water (washing) | 2-5 m³/day | 8-20 m³/day | 20-50 m³/day | C – estimate |
| Compressed air | not required | 0.2-0.4 m³/min | 0.4-0.8 m³/min | C – estimate |
| Drainage | floor drain at washer | channel along wet end | channel + settlement pit before discharge | B – industry |
Where grid power is weak, biomass or gas carries the drying heat and electricity drops to fans and conveyors – typically 30-40% of the figures above. Figures marked C are typical, to be confirmed by test.
Installed Plants, Every Machine Ours



Tell Us Your Material And Capacity – We Size The Line
- Material, variety and initial moisture
- Fresh input per day or per hour
- Target final moisture and finished grade
- Available heat source and factory dimensions
Prefer email? Write to info@tondemachine.com or WhatsApp +86 185 0387 4173. Our engineers reply within one working day.
One Supplier Draws The Layout With The Quotation
A layout drawing is not a favour after the sale – it is how a quotation becomes honest. We draw the chain on your floor plan before you commit: equipment positions, aisle widths, power drops, drain runs, door swings and where the trolleys and bins stage between batches.
Because every machine in the chain – washers, cutters, belt dryers, rooms, mills, packers – is built in our own factory, the layout is drawn from equipment dimensions we manufacture, not from a catalogue we hope will fit.
That is also why our landed-cost quotes carry the full utility and civil scope on one page: the same team that sizes the dryer sizes the power feed, the steam line and the drainage it needs.
Straight, L or U – Which Fits Your Building
| Option | Best for | Trade-off |
|---|---|---|
| Straight | Continuous lines, long narrow sheds | Simple flow, fewest conveyors; needs the full length in one hall |
| L-shape | Batch rooms + belt mix, corner buildings | Turns the flow 90° at the dryer discharge; adds one transfer conveyor |
| U-shape | Packing-heavy plants, square buildings | Intake and dispatch share one wall; needs a turnback aisle and stricter zoning |
The turnback in a U-shape is also a hygiene boundary: wet end inside the U, dry end and packing outside it.
Send Your Material Data – Get a Line Layout & Price
- Daily or hourly fresh input and target final moisture
- Available heat source: electric, steam, gas, biomass or diesel
- Factory length, width and clear height
- Target market grade and packing format
Prefer email? Write to info@tondemachine.com or WhatsApp +86 185 0387 4173. Our engineers reply within one working day.
Installations and Assembly



What To Confirm Before Ordering
| Check | What to measure | Why it bites later |
|---|---|---|
| Power feed | Transformer capacity vs installed load, +30% margin | A line that outruns its transformer throttles every zone |
| Floor slab | Thickness, level (±5 mm/10 m), point load | Belt lines are aligned on the slab – poor levels show as tracking faults |
| Drainage | Slope to drain, settlement pit capacity | Wash water carries soil and sugar; no drainage means no hygiene |
| Steam or fuel | Boiler capacity or biomass storage space | Fuel storage is a building decision, not an equipment one |
| Access | Container truck route, unloading space, door sizes | Modules that cannot reach the hall get unloaded by crane, at a price |
| Expansion | Space for one more room or one more belt section | Most plants grow within two years – leave the lane empty |
How To Read The Numbers On This Page
About the numbers on this page. Capacity, temperature and moisture figures are industry-typical values for this material. Energy consumption, utility requirements, floor space and payback are engineering estimates and are marked typical, to be confirmed by test. We confirm every figure against a drying test with your own material before quotation. Price ranges are indicative ex-works figures and exclude freight, customs clearance, civil works, utilities, installation and commissioning – equipment typically accounts for 35–55% of a landed project budget.
Frequently Asked Questions
What is the minimum building for a usable plant?
A single heat pump room with washing and packing fits an 8×6 m shed with 3.5 m clear height and an 18-25 kW feed. It processes 1-2 t/day of fresh material and can grow with more rooms.
Can I run a line on a generator or weak grid?
Yes, with planning. Biomass or gas carries the heat and electricity drops to fans and conveyors – typically 30-40% of the installed figures above. We size the generator against the actual motor start-up sequence, not just the running load.
How much steam does a drying plant need?
Only lines with blanching or steam heat need a boiler: roughly 0.3-1 t/h for a room plant up to 2.5-6.5 t/h for large continuous lines. Heat pump and direct-fired lines need no steam at all – it is a heat-source choice, not a requirement.
Does the floor really need special construction?
The wet end needs washable, drained, food-grade floor; equipment zones need 3-5 t point load capacity. A belt line aligned on a soft or unlevel slab will fight tracking problems for its whole life.
How are the machines shipped?
Knock-down in 40HQ containers: a room plant in 1-2, a batch system in 3-5, a full continuous line in 6-12. We provide the container plan with the layout so the building access is planned around it.
Do you provide the layout drawing before I pay?
Yes – the layout drawing and utility specification are part of the quotation, drawn on your floor plan. We will not quote a line we have not laid out.
The Dryers Used In This Line
Every line is built around one of these machines. Compare them, or send us your material and we will specify the right one.
Continuous Belt Food Drying Machine500-3,000+ kg/h, 1-5 layers, ambient to 120 degrees C, multi-zone PID control.View machine details →
Industrial Heat Pump Food Drying MachineClosed-loop batch drying rooms, saves 60-75% electricity, gentle 20-80 degrees C.View machine details →
Heat Pump Drying Room for ChiliPurpose-built chili drying room: staged recipes, high load per batch, low energy cost.View machine details →
Hot Air Circulation Drying Oven48-240 trays per batch, SUS304 body, up to 50% thermal efficiency.View machine details →
Double Door Hot Air Drying OvenCT-C batch oven: 60-480 kg per batch, 24-192 trays, steam or electric heating.View machine details →
Small Single Door Drying OvenCompact starter oven: 24 trays, 40-60 kg per batch, plug-and-play operation.View machine details →
Microwave Vegetable Drying MachineDries and sterilizes in minutes at 2450 MHz, 16-200 kg/h dehydration capacity.View machine details →
Food Freeze DryerVacuum sublimation keeps 97% of nutrients, color and aroma; 25-year shelf life.View machine details →Other Drying Lines In This Series
Industrial Chili Drying Line – 500 kg to 8 TonDehydrated Onion Production Line – Onion FlakeFood Drying Line Cost and Payback – Budget, RuGarlic dehydration lineMango drying lineMixed vegetable dehydration lineGinger & turmeric lineBanana & plantain lineMulti-product line (hub)Mushroom drying lineFish & seafood lineJerky & pet treats lineCassava & flour lineTomato & berry lineNon-fried crisps lineRoot vegetable dehydration lineCoffee, cocoa & nut lineHerb & spice lineDate, fig & jujube lineTea leaf lineTurnkey processPre-treatment linePost-treatment line
Request Your Turnkey Quotation
- Factory-direct price, no middleman
- Process design, layout drawing and utility specification
- Drying test with your own material before quotation
- Worldwide shipping, installation and remote commissioning support
Prefer email? Write to info@tondemachine.com or WhatsApp +86 185 0387 4173. Our engineers reply within one working day.